Welcome to the Community!

Find answers, ask questions and share your favorite stories with our community of boaters.

cancel
Showing results for 
Search instead for 
Did you mean: 

Browse the Community

All Recent Activity

Lofrans windlass solenoid.

Hi fellow sailors,Anyone know where the solenoid breaker is located on a 2002 380 Sundancer?My windlass would not work yesterday for the first time.  Thanks in advance for your reply

rando by Guest Contributor
  • 5 Views
  • 0 replies
  • 0 likes

48DA windshield wiper noise

Hey folks,When I turn my wiper switch to INT I get a very loud hum from the dash area that some what sounds like an alarm. The wipers don't work in this mode but work fine in the normal mode. Does anyone have any ideas what this might be? 

Tcollins by Guest Contributor
  • 16 Views
  • 0 replies
  • 0 likes

300 R torqmaster blowout

What speed is the torqmaster lower unit on a 300R 4stroke capable of before blowout will become a concern?  Boat is a triton  21 bass boat about 1.25 below pad frequently touching 90 MPH.  I have another prop that is capable of a couple more MPH but ...

Logan by Guest Contributor
  • 8 Views
  • 0 replies
  • 0 likes

2007 SLX 250

I have a 2007 SLX 250 that will not rev above 3500 rpm. It appears to backfire with a loss of power if I open the throttle above this figure ; especially when putting the engine under load. Iv'e spent thousands of Euros trying to cure this problem an...

JJ_s by Guest Contributor
  • 15 Views
  • 0 replies
  • 0 likes

Prop Refurb/Repairs

I got a new Bravo I FS this year that I really like. I managed to idle it through some sand a couple times this summer. That put a few pits in the leading edges of the blades and I wondered what the  best place is to send it to this winter to bring i...

BW by Guest Contributor
  • 19 Views
  • 0 replies
  • 0 likes

2007 SLX 270 - Buoyancy

HiPlease can someone advise on the built-in buoyancy of this Sea Ray.We require a buoyancy certificate in South Africa and i'm struggling to find this out.There should be a volume of foam that is built-in, in litersThanksPaul 

pacol100 by Guest Contributor
  • 21 Views
  • 0 replies
  • 0 likes

stern seat replacement

Hello Everyone, My 2001 180 Dauntless held up very well against Hurricane Ian. The bad news is the stern seat with hinge lid and cushion was lost.It will likely be easier to have a new one made, then to find a new one to purchase. However I am striki...

Gasket

Hi!I am in the process of starting the restoration on a wooden console Montauk.  I am trying to find the gasket that goes around the window.  Ours has shrunk with age and the windows rattle.  I'll be refinishing the wood too if anyone has suggestions...

IMG_4182.jpeg IMG_4181.jpeg IMG_4180.jpeg
BeccaB by Guest Contributor
  • 18 Views
  • 0 replies
  • 0 likes

2006 Sundancer44 transducer replacement

Hello all,I have a 2006 which requires the transducer to be replaced. Is this something which requires the boat to be hauled or can this be replaced while in the water?  Also, since I believe this is the original equipment, how do I know what make/mo...

FFFFAST by Guest Contributor
  • 52 Views
  • 0 replies
  • 0 likes

Rubberpad

Pls help.My 9 contact in rubberswhich is not funktion.Can anyone help with info on the 6 wires it is connected to.Mogens 

Welcome, Boaters!
Brunswick wants to connect boaters from all walks of life, which is why we’ve created a space for owners of some of the marine industry’s most-loved brands. We hope you'll use this platform to connect with others who share your passion.

Click into a specific conversation or brand to begin exploring!