Hi- new to the group so pardon...

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-25-2022 03:57 PM
Hi- new to the group so pardon me if this is already in the archives...
I'm about to pull the trigger on a 2003 340 Sundancer DE- 8.1 Mercs, V-drives with only 300 hours. The boat is clean, clean, clean inside and out except canvas (ready for the dumpster) and outdated but workable electronics.
I plan to do a full survey including engine compression, etc. but there aren't a lot of maintenance docs so elbows and risers are a ?
Anything the group thinks I should be particularly aware of or potential problems I should be looking for?
I'm not new to boating but transitioning from sail to power (wife wants to go fast...)
Any/all advice is appreciated.
Kt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2022 02:57 AM
The boat is a cruiser, not a go fast boat, but will definitely do circles around a blow boat...
Yes a good survey is a worthy investment. IMO disassembly of at least one exhaust riser / elbow (w/ replacement of the single usage gasket) is a good idea to permit inspection of the internal raw water gasket is appropriate.
All the normal stuff like checking all systems and running gear should be performed. My 2000 380DA was built w/ 5 flooded cell batteries. Those had a life of about 5 years. I switched to six Lifeline GPL-31XT because they have 25% more capacity than all other AGM and because of about twice the lifetime. Also maintaining the electrolyte level in flooded cell batteries is a royal butt pain, not required w/ AGM.
https://lifelinebatteries.com/products/marine-batteries/gpl-31xt/
It is possible / likely that bedding on hull stuff is required to be redone. Might not show up on a survey unless loose.
FWIW, use PTFE thread on the new canvas. That thread is impervious to sunlight degradation and will last forever. Here is the topic on my custom canvas enclosure.
http://forum.sailrite.com/wingless-custom-enclosure_topic2801.html

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2022 04:25 AM
Not a go fast boat? I've spent the last 12 years a 6-7 kts- fast is a relative term 🙂
No question on the AGMs being the best way to go but what a shot to the wallet!
Appreciate your help!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2022 05:37 AM
The exhaust on my 454 MAG MPI Horizon engines are different than the dry joint on your 8.1 engines. The dry joint is superior.
On mine I needed to perform an annual inspection, followed by mental justification for continued usage. Uncertain if annual disassembly / inspection is also appropriate for your engines.
The parts cost on mine is ~$5K and I would get 3-5 years of usage before having to discard the OEM parts.
Fortunately my exhaust redesign w/ OEM parts has resolved that problem.
My analysis shows the cost of AGM versus flooded cell to be a wash, when lifetime is included. My boat has decent access for the battery bank and it really sucks to check / top off the electrolyte level. AGM is the way to go.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2022 06:52 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2022 07:19 AM
Heat exchangers were original to the boat when I bought it so 9 years old at the time. I spent a good amount of time chasing heating issues, loss of coolant, etc. until I replaced the heat exchangers (engine, transmission, and oil cooler on each engine).
Typically when I buy a used gas boat, I always replace the manifolds (and potentially risers... more on that) if I can't verify when they were replaced. I've now added heat exchangers to that list. If I can't verify they've been done in the past 7-8 years, just swap them out. I went aftermarket with Mr. Cool exchangers - they are about 1/2 the cost of OEM. I've been running them for 6+ years now without issue.
On the risers, my understanding is they are aluminum on the 8.1 motors with the dry joint system. you only need to replace the manifolds and I do them every 5 years like clock-work. You could probably milk it longer but the damage done if they fail is catastrophic so not worth the gamble in my opinion. You have 5 years runway, just plan on the expense over 5 years and it's not that bad.
Canvas - one thing that's nice about having a popular production boat is you can buy factory canvas from great lakes boat tops. They made them originally for your boat. Just give them your hull number and they can make you new ones.
Pre-covid - they were much less expensive than going to local shop to make custom canvas. I think I replaced my full canvas set for $2800. That said, the front isinglass would always start fogging and greying after 2 years. I've replaced the front glass twice now. The isinglass panels used to be $700 per set which is pretty cheap so I looked at these as 3 year throw away items.
Post-covid - great lakes and RNR just plain stopped taking orders, prices have gone up, and the wait times are long. I recently got a "camper canvas" setup custom made + replaced the front glass since it was fogging again. I finally decided I wanted to do it right and not wanting to replace the glass again for my ownership of the boat. My local canvas guy replaced the front windows and port / starboard side with poly and it is night and day in quality. They are great!!! definitely not removable or storable; the material is THICK but we never pull off the front stuff anyway.
Bedding on deck hardware is real too... I always thought i was getting excessive moisture in the cabin when we bought the boat but could never really pin point it. We're in San Diego and it doesn't rain all that often. It would rain, leak, and then most likely dry out before we got back down. One time I came down and there was water on the galley counter and bed. Took me a while to figure out but it was the deck rails that would hold the sunpad. 7 of the 8 through hull bolts were leaking, it would then travel through the headliner all over the boat.
Shaft seals are another one. Those are about a 10 year servicable lifespan. Mine started leaking right at the 10 year mark. Replaced with PIY dripless. if yours haven't been done, be ready.
That's a lot of typing and I could keep going! I have a dashboard / maintenance spreadsheet I'd be happy to share with you. I went through all the manuals for the motors, gen set, and advice from folks over the years to track when maintenance items needed to be done and when I did them last. send me your email address and I can send it over if you're interested.
The thing that concerns me the most about your boat based on the description is the 300 hours, assuming those are the original un-rebuilt motors. The worst thing you can do to a boat in my opinion is to not use it. I'd rather buy a boat with hours commensurate to regular usage based on age with a well-documented maintenance history. You wake those motors out of a 20 year slumber and start running them, you're going to start seeing all the original parts failing that normally would have been replaced with normal usage.
Bottom line for me... the 340 for has been a great boat. My broker told me at the time he sells the most of them of all Sea Ray models - it's people upgrading like me going from the 260 -> 340 and downgrading, want an easier boat to solo handle and it's crazy expensive. My kids are 6 and 3. I figure in 2-4 years, we'll "need" more space and would like to have a real stand-up shower and a stateroom. For a small family of 4 or a couple, it's a great size boat... we could even make it work with bigger kids if it doesn't make sense financially and/or we're just not using it enough to justify tripling the cost to go bigger.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2022 08:24 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-12-2022 09:03 AM
Thank you for your comments. We just bought a freshwater 1997 SeaRay 330 Sundancer with 700 hours. Could you please email your maintenance spreadsheet to me at tacatania@yahoo.com. Thank you!
Tom Catania in Las Vegas
