Props & Accessories
cancel
Showing results for 
Search instead for 
Did you mean: 

Conversations

Prop Refurb/Repairs

I got a new Bravo I FS this year that I really like. I managed to idle it through some sand a couple times this summer. That put a few pits in the leading edges of the blades and I wondered what the  best place is to send it to this winter to bring i...

BW by Guest Contributor
  • 19 Views
  • 0 replies
  • 0 likes

Prop Selection for 120mph monohull

Dears,We want to hit 120mph with twin 500Rs on our 9.5m monohull.  I'm not overly confident in going with a cleaver as I had not so good results with them on outboards so far.  Could a bravo 1 or a Max 5 work, had these up to 100mph before?  There is...

44.JPG

2006 Caravelle Interceptor Prop recommendation

Greetings, I have a 2006 Caravelle 232 Interceptor 350 Merc Bravo one.  Looking for thoughts on prop options.  I'm thinking of trying a 21 or 23 pitch Bravo 1 FS or a Revolution 4.  Any experts with pros or cons of each?  Thanks all! v/r Dan

Dan13 by Guest Contributor
  • 80 Views
  • 0 replies
  • 0 likes

Silhouette with 300R propeller help

I am trying to figure out the best propeller to use on my silhouette modified tunnel for water skiing. I was running a 17" pitch High 5 on the old  promax 300 with a sport master gearcase but it doesnt seem to work very well on the new 300R with a to...

wjb274 by Guest Contributor
  • 833 Views
  • 0 replies
  • 0 likes

Rev 4 Lab Finished

Has the revolution 4 lab finished props been discontinued with the inception of the new Ventera?  If so, is their any discernable difference in performance between a comparable revolution 4 lab finished prop and lab finished Ventera?    Specifically ...

TH by Guest Contributor
  • 313 Views
  • 0 replies
  • 0 likes

250R Sport Master Prop Advice

I just bought a 250R and it was installed on my 2009 Ranger Z21 (lead sled) and the dealer put a Fury 3-bladed prop on it and I am thinking I need to go to a Mercury Racing prop instead. I am getting about 65 MPH at about 6,100 RPM. The hole shot cou...

lwheeler by Guest Contributor
  • 259 Views
  • 0 replies
  • 0 likes

Resolved! CNC cleaver test program

Hi!I hope you are well I have a Phantom 25 1985 model straight V bottom with a Max5 27 15,25 ST. It runs 93,3 mph at 6,200 rpm. Propshaft 2 inches above the bottom. I seriously consider to buy a CNC 5 bl cleaver - 14,75 inch 18 rake 27 pitch. However...

Phantom 25 pp 040522.jpg
ToffenG by Guest Contributor
  • 769 Views
  • 2 replies
  • 0 likes

Revolution 4 XP details

@NickPetersen  I would like to know if the profile of the new 15" dia Revolution 4 XP is same as on the smaller 14,6" models? Any differences on rake, cup etc? Which pitches have most cupping odds or even? .5 pitches are made by removing some cup rig...

Nitra22 by Guest Contributor
  • 667 Views
  • 1 replies
  • 0 likes

Propeller advice wanted twin 300R on 35ft deep v cc

Looking for propeller advice for my boat.Boat details: Marlin 350 SF, 35.6 ft long, deep v 24 degree deadrise, euro transom style, engine center to center 27", engines twin 300R HD CMS, turning inwards, current tie setting 1/4 inch toe in (experiment...

Rouven036 by Guest Contributor
  • 2010 Views
  • 6 replies
  • 0 likes

props for new 30 Phantom twin 300r power

I have a 2022 30' phantom vee bottom, twin 300r motors. I've run 104mph with Dewald 5 blade over the hub props 32"x 15" x 17 degree rake @6400 rpms (the boat handled very good). I've run 96.8mph @6500rpms  with a set of standard looking 32" full barr...

jrod19 by Guest Contributor
  • 1786 Views
  • 5 replies
  • 2 likes

Bass Setups

Let's talk setups on bass boats, whether you're fully loaded with a partner, or running light for top end, what's your favorite setup between props, engine height, setback, etc? Post up photos!