Sea Ray

We didn't have a good way to siphon other than just sucking on the tubes with our mouths.. obviously not healthy.. so we've tried the other way blowing through the line into the tank. No restriction and you could hear the fuel bubbling. Actually, the thought was that we weren't getting as much resistance as we should be. We've swapped fuel likes from port to starboard from the tank to the Parker electronic fuel valves.. that wasn't it.

Current thinking is there's a crack in the pickup that's letting air in the system. We're going to throw 15 gallons in the tank to see if that "fixes" it.. or at least helps diagnose the problem. Idea being that the crack was low enough down that it was fine what I was running and had fuel, then I just hit the point where air was getting in the way of suction.

Last big trip I made I got pretty beat up.coming down the coast with weather... if the pickup was weak, that definitely could have over stressed it.

Problem with the pick-up, we can't figure out how to access and remove it without drilling a hole in the deck. Otherwise, we'd just pull it and check. Was curious if anyone on here had a trick to doing it in a 340 without drilling.

Open to other ideas!! Thanks!!

Doesn't the boat have these fuel shutoff solenoid valves?

Were they defeated or opened for the test?

Here is the image link showing the fuel solenoids.

https://live.staticflickr.com/4745/40465168062_560799e07e_b.jpg

It has the parker hannifin fuel valves - SEA RAY PART# 1791155. We swapped the starboard motor valve with the one for the generator and tried enabling the bypass. That was my initial thought, that is was the valve... no change when doing both of those

Good effort.

The valves Sea Ray used on my boat have a twist knob providing an on position and and electrically controlled position.

Your tanks should be made by Florida Marine Tanks, go to their website. If they are Florida Marine Tanks like mine your pickup line might be aluminum fixed in the tank. That means you can’t remove it and there is no way to access the screen at the end at end ( if there is one ). At one occasion I had to blow compressed air into the tank just to make sure the line was free of obstructions. Did you try to suck fuel from a portable tank? Was there a difference?

Thanks BigTuna... that's good info that I was wondering about. I had a feeling they were fixed in the tank. Problem is still being troubleshot. I can't imagine what's involved if I ever have to replace the tanks... and hopefully I don't ever have to in my ownership! Finally threw in the towel with my hopes at getting it running where it broke down and had it towed back to the home port.

My mechanic ended up taking the cool fuel module off the motor so he could test it on a bench. Ran it off a remote tank like you suggested and it seemed to be working fine. We're trying to isolate if it's a problem on the motor vs. the tank-side. Current theory is going back to the Parker Hannifin value.

We think it failed and closed which starved the engine of fuel. When we tried to use the bypass, we didn't think to prime the 8 feet of fuel line from the valve to the cool fuel module. Mechanic had Mercury on the phone to help troubleshoot and they were saying the pump wouldn't be able to clear that much line of air. On a shorter hose (2 feet) on the bench, it would be ok. That's why we're thinking it worked on the bench but not in the boat.

Another data point - he has a Power Probe where you can power basically anything off 12v. When we tried to power the valve directly, it would trip the circuit of the tool.. that's what's leading us back to the valve.

Interesting side note - I couldn't find the Parker Hannifin valves anywhere online accept on ebay. I was a little leery of ordering this part through an ebay seller but since my local Sea Ray dealer never got back to me, figured why not give is a shot. I was surprised that the return shipping label listed Brunswick Boat Group out of TN. 1/2 wonder if Sea Ray is selling these online through Ebay or their drop shipping direct for a reseller. Either way, think it's a legit OEM part. I might just order an extra one since they seem hard to come by.

We're going to try to prime the line and swap the valve Mon/Tues this week. I'll keep the group updated so it's on the forum and hopefully helps someone out that runs into this in the future.

Thanks BigTuna and Wingless for batting around ideas with me!

... and Vinster!

I have/had a similar issue and I used the process of elimination. In my case I isolated the problem to the high pressure fuel pump. And since I am doing that I am replacing the fuel cooler as well. However I don’t think the eight feet of fuel line/hose should be an issue.
You have 2 fuel pumps a low pressure and a high pressure. In fact you probably have a good 4-6 ft of fuel line between the tank and the engine. Had to do most of the work myself after begging and chasing mechanics to do their job, and coming up with a new excuse every time as to why they have to go back and forth. As far as parts goes, I learned that whenever I buy a part online I have to order an extra one due to high rate of failure. I found that local searay dealers don’t care about carrying parts or providing services unless your boat is less then 5 years old as very clearly a local told me last year.

@BigTuna we started at the fuel rail with a pressure gauge and then worked our way down the system. First thing we noticed was there was no fuel in the rail, traced that back to the fuel filter bowl and that was empty. Filled up the fuel filter bowl with a gas can and it fired right up until it ran out of fuel again. Tried the bypass on the Parker valve, that didn't help. Then tried replacing the low pressure pump, that didn't work.

The cool fuel modules I replaced when I bought the boat about 5 years ago. It sat for a while (window was selling after her husband died and took her a while to get to that point of selling it) and the ethanol broke down the paint and sent it down the rail. had to replace all the fuel injectors as well.

I'm kind of wondering if I should be looking to replace the fuel lines and how much ethanol breaks them down. Part of me wonders if the lines are just compressing when under pressure and choking off the fuel flow. Boat is a 2006. Have you replaced the fuel lines or does anyone on here know what the service life is?

Will post when I learn more

I had similar issue with CFM and paint particles. Our caused the secondary pump to fall. I chose tho replace the $1200 CFM. Two of my injectors were bad so I removed the rail and had the injectors cleaned. That was 6 months ago. Mechanic used computer to perform drop test under power, 2500 rpm. All good. As for the fuel lines, they can have coating of Ethonol crud if engines not used often - fix = remove, clean, reinstall. I always use rec fuel and still use fuel treatment with corrosion protection.

I agree with Vinster. You should always use stabil 360, especially if you don’t use your boat often. No I didn’t have to replace the fuel lines. In my case the high pressure fuel pump and cooler made a huge difference. The fact that your high pressure was replaced 5 years doesn’t mean that it didn’t go bad especially if doesn’t get used frequently.

yeah.. i use Stabil every fill. I keep a case of it on the boat. We've got 2 little kiddos so sometimes there's big gap in when we can get down there... b-day parties, soccer, etc.

High pressure is good. If you get fuel into the CFM, it pumps into the rail and the boat runs. We're going to mess with it more tomorrow... I'll keep you posted.

Thanks for all the ideas and discussion. Very helpful!

Just wanted to close out this loop and thank everyone again for the comments and suggestions. I ended up buying a 10 foot fuel line so we could run the motors off opposite tanks and eliminate variables. Port side motor (good motor) ran off both thanks so that eliminated the tank. Filled the 10 foot line with fuel and couldn't get the pump on the starboard motor (bad motor) to pull fuel through so we went back to the CFM.

Ended up buying a full CFM assembly vs. swapping more parts in the CFM and that solved my problem. Ironically, the CFM was the first hunch but my mechanic (and buddy) was trying to eliminate all other variables before throwing a $1300 part at the problem without knowing for 100% certainty that was the issue.

Current theory is that the electronic fuel value went bad and failed closed; when the pump ran dry, it cause some type of unknown issue and the CFM to fail. Replacing the fuel valve and CFM got me back up and running.

Adding to the ToDo list for the winter is to replace all the fuel lines (figure it's cheap insurance and I won't ever have to do it again in my ownership of the boat.

As for Stabil - I use it EVERY fill up on all my boats. I had the paint issue with the CFMs 5 years ago when I bought the boat. Replaced the CFM and all the injectors at the time.

OK... i think I declared victory too early and need some help. When I posted that last time, found out that fuel valve wasn't actually swapped yet and was just in bypass mode. When the new valve went it, the motor was starved of fuel again. Does anyone know how the fuel valve is getting power? Thinking that the faulty valve may have blown a fuse somewhere and we're trying to figure out where that might be. I don't think it's getting power to open up.

I tried looking at the wiring diagrams in the manual but didn't have much luck finding it.

The documentation provided w/ my 2000 380DA also does not show electrical connections to the hull fuel shutoff valves.

An extended documentation package I have shows a two wire harness feeding that shutoff valve, driven by a splice for the wire feeding the engine electrical fuel pump, with Gray being signal and Black being ground.

That documentation shows the linked Packard Electric 280 Series connectors between the existing fuel pump feed, as-shown starting on page 23 of 111 in the link.


https://www.reynoldsonline.com/ASSETS/DOCUMENTS/ITEMS/EN/12033769_Spec.pdf

Shoot.. so it sounds like the valve and fuel pump are all.on the same circuit. If that's the case, it would be all or nothing. I'm wondering if I just have a bad electrical connection somewhere.

When the engine power is toggled from off to on, prior to starting the engine, is there audible fuel pump noise, until the fuel pump pressure is reached? My engines make that fuel pump noise prior to me toggling the switches to the start position.

If so, then can a DC voltage meter be connected to the hull fuel shutoff valve electrical connections to determine if those valve are also receiving power, to command that they open?

Please provide the results of that measurement.

Does your engine fuel pump have those linked 280 Series connectors, w/ a splice feeding the hull shutoff valves?

flying today and tomorrow; back at the boat on Thursday. I'll circle back. Thanks

I had a similar issue after finding paint particles in the bottom of the VFM fuel bowl. Some of that crud found its way into the pumps, both of them. Mercruiser issue at manufacture but never issued replacement. The only fix I found that worked is to replace the CFM. For $1200, you get all new parts. Its an easy install, you'll need a fuel line tool about $12 at auto parts.

Ok... made it back down to the boat and confirmed everything runs fine as long as the fuel valve is in bypass mode. checked the voltage at the valve and it was all over the place between 0-13v so there's an electrical issue. @wingless - yes, it has the 280 type of connectors. looks like one off the ECM and there's a splice to the fuel pump and the fuel valve. I think that's the source of my problems. Some corrosion causing resistance and the irregularities in the voltage causing problems.

Cut out and pulled that piece of the harness. Going to rebuild the connections and rewire and see where that lands us.

@vinster - I replaced both the CFMs and all the injectors when I bought the boat 5 years ago. Ever since then, I use fuel stabilizer every fill. That said, we swapped the CFM on the "bad" motor with a new one... i'm not convinced the old one is bad and it maybe have been my electrical issue... but not going backwards at this point. (any thoughts on how to test a CFM on the bench to see if it's good?... I'm going to hang onto the old one anyway)

Making progress. Commentary welcome and I'll make sure I post updates

Thanks for the update.

Yes, corrosion is bad and can cause problems.

It may be that the measured voltage between 0 and 13 VDC might be normal, caused by the measurement tool and not indicative of a problem.

It is "easy" to be fooled by a digital voltage meter, making extra steps required to understand reality.

On my boat, the fuel pump is energized, then stops. That would be observed as 13VDC, then 0VDC.

The Mercruiser engine uses that Packard Electric 280 Series connector, from the engine harness to the fuel pump. Sea Ray created a splice harness, w/ pigtails to go between those Mercruiser fuel pump connectors and w/ a long fly lead to power this hull fuel shutoff valve.

It should be possible to unplug this Sea Ray part, plug the Mercruiser connectors back together and turn the fuel valve to always on, to restore normal operation.

With that Sea Ray harness removed, then it should be possible to perform bench measurements to determine if good or bad.

If that harness is bad, then purchasing a replacement may cost more, but might work out better because of the special crimp tools required for the connector contacts.

As you say, don't look back. I would not waste any time on old CFM unless you are curious or need that info to further your quest to identify problem that was not the CFM!

@wingless - "It should be possible to unplug this Sea Ray part, plug the Mercruiser connectors back together and turn the fuel valve to always on, to restore normal operation." that's the state it's currently in now. my mechanic took the Sea Ray addition and will test on an omh meter on it. he was going to try to rebuild it. I'm 99% that splice is where the problem is.

@Vinster - I think you're right... why waste time. I did swap the low pressure pump in this journey. I'll probably pull that since is was basically never used and junk the rest.

Definitely looking forward to closing out this thread and getting back on the water! killed 1/2 of my summer!